From Friday, April 19th (11:00 PM CDT) through Saturday, April 20th (2:00 PM CDT), 2024, ni.com will undergo system upgrades that may result in temporary service interruption.
We appreciate your patience as we improve our online experience.
From Friday, April 19th (11:00 PM CDT) through Saturday, April 20th (2:00 PM CDT), 2024, ni.com will undergo system upgrades that may result in temporary service interruption.
We appreciate your patience as we improve our online experience.
Version 15.0.0
June 2015
This file contains important information about NI LabVIEW Remote Development Target Support, including installation instructions, configuration instructions, troubleshooting, and known issues.
Product Security and Critical Updates
Remote Development Requirements
Enabling LabVIEW Remote Development
Automating the Installation of NI Products
NI LabVIEW Remote Development Target Support enables you to develop, run, debug, and deploy LabVIEW VIs on National Instruments hardware running the Windows Embedded Standard operating system. You develop, run, and debug the VIs on the Windows Embedded Standard target from a host computer with the LabVIEW Development System. You can deploy VIs with a built installer from the host computer to the Windows Embedded Standard target. The following National Instruments hardware is supported:
LabVIEW Remote Development Target Support has system requirements for the host computer and target.
| Host Computer | Target |
|---|---|
The host computer must meet the following system requirements:
Refer to the LabVIEW Readme for additional system requirements and supported operating systems for the LabVIEW Development System. | The target must meet the following system requirements:
|
Use the following table to determine whether you need to manually install LabVIEW Remote Development Target Support.
| Hardware Device | Purchase Date | LabVIEW Remote Development Target Support |
|---|---|---|
| NI TPC-2206/2212/2215 | N/A | Download the installer and additional software from the National Instruments website. |
| Other supported hardware devices | Prior to August 2014 | Download the installer and additional software from the National Instruments website. |
| On or after August 2014 | Pre-installed with the hardware device. |
Visit ni.com/security to view and subscribe to receive security notifications about National Instruments products. Visit ni.com/critical-updates for information about critical updates from National Instruments.
After installing LabVIEW Remote Development Target Support on the target, the target must meet the following requirements before you can develop applications remotely from a host computer:
Complete the following steps to enable LabVIEW Remote Development on the target. You must restart and log into the target for changes to take effect.
Note By default, LabVIEW Remote Development is enabled if you manually install LabVIEW Remote Development Target Support. If the target comes pre-installed with LabVIEW Remote Development Target Support, you must complete the following steps.
| Note Ensure that the Run-Time Engine Version matches the version and bitness of the LabVIEW Development System on the host computer. |
The target is now enabled for remote development. Refer to the Fundamentals»Working with Projects and Targets»Concepts»Working with Windows Embedded Standard Targets topic on the Contents tab of the LabVIEW Help for more information about developing applications on Windows Embedded Standard targets.
National Instruments recommends that you disable LabVIEW Remote Development after deploying applications to targets that are not used for development. To disable LabVIEW Remote Development, complete the following steps.
For more information about security when developing and deploying applications to a target remotely, refer to the National Instruments website.
Use the following table to find solutions when using LabVIEW Remote Development Target Support and developing applications on a Windows Embedded Standard target.
| Issue | Solution |
|---|---|
| (Touch Panel and CompactRIO devices only) I cannot discover my target in Measurement & Automation Explorer (MAX) on the host computer. | On the host computer, MAX does not support discovering Windows Embedded Standard targets. |
| (Touch Panel devices) How do I select a device type on the target? | If your target is a touch panel computer, you must specify the device type in the Select device type dialog box. On the target, launch this dialog box by navigating to Start»All Programs»National Instruments»LabVIEW Remote Development»NI Device Type Configuration. Select the device type and restart the target for changes to take effect. |
| I cannot discover the target in the LabVIEW Development System using the Add Targets and Devices dialog box. | Ensure that the target meets the requirements necessary to discover a device for remote development:
|
| I cannot connect to the target in a LabVIEW project, although I can discover the target using the Add Targets and Devices dialog box. | Ensure that the version and bitness of the LabVIEW Run-Time Engine on the target match the version and bitness of the LabVIEW Development System on the host computer. |
| How do I verify that LabVIEW Remote Development is enabled on my target? | Launch MAX and select My System in the configuration tree. In the Remote Development Settings section of the System Configuration page, ensure that LabVIEW Remote Development contains a checkmark. |
| How do I determine the version of the LabVIEW Run-Time Engine enabled for remote development on the target? | Launch MAX and select My System in the configuration tree. In the Remote Development Settings section of the System Configuration page, refer to the Run-Time Engine Version. Ensure that the version and bitness match the version and bitness of the LabVIEW Development System on the host computer. |
| How do I verify that the LabVIEW Remote Development application is running on the target? | Launch the Windows Task Manager. In the Processes page, verify that the list of processes contains niLVRemoteDev.exe. If the list does not contain niLVRemoteDev.exe, you must restart the LabVIEW Remote Development application. |
| How do I restart the LabVIEW Remote Development application? | Restart the target or select Start»All Programs»Startup»NI LabVIEW Remote Development. |
| Windows Firewall blocked the LabVIEW Remote Development application. What should I do? | You must authorize the LabVIEW Remote Development application to allow access through the Windows Firewall. |
| Can I automatically log into the target? | You can configure automatic logon to the target. |
| Can I configure remote development settings for my target from the host computer? | From the host computer, you can configure remote development settings by completing the following steps:
|
| (CompactDAQ devices only) I do not have credentials to configure my target in MAX on the host computer. | Refer to the Measurement & Automation Explorer Help»Remote Systems»System Settings topic in the MAX Help for more information about configuring your target settings. |
You can access the software and documentation known issues list online. Refer to the National Instruments website for an up-to-date list of known issues in LabVIEW Remote Development Target Support.
Refer to the Fundamentals»Working with Projects and Targets»Concepts»Working with Windows Embedded Standard Targets topic on the Contents tab of the LabVIEW Help for more information about developing applications on Windows Embedded Standard targets. The LabVIEW Help is accessible by selecting Help»LabVIEW Help from the LabVIEW Development System on the host computer.
You can automate the installation of most NI products using command-line arguments to suppress some or all of the installer user interface and dialog boxes. However, starting with the August 2012 releases (products using NI Installers version 3.1 or later), you may need to perform additional steps before or during a silent installation of NI software.
If the NI product you are installing uses Microsoft .NET 4.0, the .NET installer may run before any NI software installs and may require a reboot before the installation of NI software begins. To avoid a .NET reboot, install .NET 4.0 separately before you install NI software.
For more information about automating the installation of NI products, refer to the following KnowledgeBase articles:
Copyright
© 2013–2015 National Instruments. All rights reserved.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.
National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
End-User License Agreements and Third-Party Legal Notices
You can find end-user license agreements (EULAs) and third-party legal notices in the following locations after installation:
U.S. Government Restricted Rights
If you are an agency, department, or other entity of the United States Government ("Government"), the use, duplication, reproduction, release, modification, disclosure or transfer of the technical data included in this manual is governed by the Restricted Rights provisions under Federal Acquisition Regulation 52.227-14 for civilian agencies and Defense Federal Acquisition Regulation Supplement Section 252.227-7014 and 252.227-7015 for military agencies.
IVI Foundation Copyright Notice
Content from the IVI specifications reproduced with permission from the IVI Foundation.
The IVI Foundation and its member companies make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The IVI Foundation and its member companies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Trademarks
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies.
Patents
For patents covering the National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.
375323A-01