Browse Teaching Resources

1-50 of 95 Results
Power Electronics

by Dr. Nicola Femia | University of Salerno, and Texas Instruments

Students complete hands-on labs that cover the fundamentals of DC-DC linear regulators, DC-DC buck regulators, DC-AC inverters, and AC-DC rectifiers. Designed for NI ELVIS III.
Analog Electronics

by Enable Education

In this lab manual students simulate, build, and analyze circuits to learn about behaviors, characteristics, and applications of common silicon-based components. Designed for use with NI ELVIS III.
Introduction to Circuits

by Enable Education

This course covers the fundamental concepts of circuit theory and analysis through simulation in Multisim Live, and real-life circuit-building. Designed for NI ELVIS III.
RC Circuits

In this lab students will learn about resistor-capacitor circuits, make calculations, and confirm their understanding in hands-on circuit building. Designed for use with NI ELVIS III.
Thyristors

In this lab students will be observing the use of thyristors in hands-on circuit simulation and circuit building. Designed for use with ELVIS III.
Signal Conditioning

In this lab, students complete activities where they prepare measurement signals to be digitized. Designed for NI ELVIS III.
Introduction to DSSS (Spread Spectrum)

by Emona Tims

In this lab, students will recover a variety of messages from an amplitude modulated carrier signal and develop an understanding of the demodulation process. Designed for NI ELVIS III.
Ohm's Law

In this lab, students will learn about Ohm's law using circuit simulation in Multisim Live and hands-on application with NI ELVIS III. Designed for use with NI ELVIS III.
Kirchoff's Current Law

In this lab students will learn about Kirchoff's Current Law and how to calculate unknown values using KCL, then confirming with real circuits. Designed for use with NI ELVIS III.
Op-Amps

In this lab students will be learning about the open-loop behavior and theory of an operational amplifier (op-amp) through hands-on applications. Designed for use with NI ELVIS III.
Digital Electronics

by Enable Education

Students simulate combinational and sequential circuits and deploy them to an FPGA target. Designed for NI ELVIS III.
Problems and Explorations in Microelectronics with NI myDAQ and Multisim

by Dr. Ed Doering | Rose-Hulman Institute of Technology

For faculty wishing to incorporate portable instrumentation into their analog electronics courses, this text provides forty end-of-chapter-style problems covering basic concepts in diodes,...
Signals and Sensors

by Enable Education

In this lab, students will learn about sensors and the process of measuring different types of physical signals. Designed for NI ELVIS III.
Amplitude Demodulation

by Emona Tims

In this lab students use the Emona Communication board to learn two methods for amplitude modulation (AM) and demodulation. Designed for NI ELVIS III.
Zener Diodes

In this lab, students will complete hands-on activities with Zener diodes to validate and explore their operation, applications, and uses. Designed for use with NI ELVIS III.
ADC and Sampling

In this lab, students will learn about analog-to-digital conversion (ADC), sampling, and their characteristics. Designed for NI ELVIS III.
ECG Circuit Project

Students design an Electrocardiogram (ECG) circuit using Multisim Live, and then build and validate the circuit to produce the most accurate possible heartbeat reading. Designed for NI ELVIS III.
Kirchoff's Voltage Law

In this lab students learn how to apply Kirchoff's Voltage Law through online simulation and then real life application. Designed for use with NI ELVIS III.
Labs for Analog and Digital Courses using NI ELVIS II and NI Multisim

by CEDES Don Bosco

This comprehensive laboratory set for analog and digital curriculum teaches DC circuits, AC circuits, analog electronics, and digital electronics. Designed for NI ELVIS II/II+.
Linear Regulator Error Amplifier Operation

by Texas Instruments, and Dr. Nicola Femia | University of Salerno

In this lab, students will investigate the properties and responses of the error amplifier generated by the gate driver voltage in a linear regulator. Designed for NI ELVIS III.
Teaching Digital Logic Fundamentals

by National Instruments

This series of tutorials teaches students digital logic fundamentals, including logic gates, logic simplification, digital comparison logic, and digital counters.
Optocouplers and IGBTs

In this lab students will be looking at two devices used as electronic switches: optocouplers and insulated-gate bipolar transistors (IGBTs). Designed for use with NI ELVIS III.
Instrumentation Amplifiers

In this lab students will be looking at a configuration of op-amp amplifiers called instrumentation amplifiers through web-based simulation and hands-on circuit building. Designed for use with NI...
Measurement Software and Analysis

In this lab, students will complete activities in data acquisition, such as storing, analyzing and presenting data on a PC. Designed for NI ELVIS III.
Voltage Dividers and Resistance Bridges

In this lab students will learn how to recognize and analyze voltage divider and resistance bridge circuits through hands-on work. Designed for use with NI ELVIS III.
Linear Regulator in Open Loop AC Operation

by Texas Instruments, and Dr. Nicola Femia | University of Salerno

In this lab, students will investigate the MOSFET in AC operation, which is of interest in linear regulator applications. Designed for NI ELVIS III.
Diodes

In this lab students learn theory, simulate, build, and analyze circuits to examine the main characteristics and functions of a diode. Designed for NI ELVIS III.
Series and Parallel Capacitors

In this lab students will learn about capacitors through web-based circuit simulation and hands-on circuit-building. Designed for use with NI ELVIS III.
MOSFETS

In this lab students will be looking at MOSFETs: their operation, applications in real-world examples, and hands-on experiments. Designed for use with ELVIS III.
Voltage Level Indicator Project

In this lab students will design and build a voltage level indicator, applying the knowledge they have learned into a hands-on application. Designed for use with NI ELVIS III.
Lab 3: Amplifier Frequency Response

by National Instruments

This lab introduces students to the importance of frequency response when designing circuits. Students will investigate the frequency response of two amplifier circuits, one made with transistors and...
Teaching Electronics in Technical and Vocational Colleges

by Alexander McGlashan | Niagara College of Applied Arts and Technology

This set of labs is aimed at teaching introductory and advanced electronics concepts for engineering technology and technician programs.
Diodes in a Rectifier

In this lab students learn about the applications of diodes in rectifiers and examine the components and operations of a full-wave rectifier. Designed for use with NI ELVIS III.
Power Electronics Fundamentals

by National Instruments

The Power Electronics Fundamentals tutorials series provides an overview of power electronics basics, including topics like rectifiers, inverters, and regulators.
Complementary Labs for Electrical Engineering

by National Instruments

Complementary Labs for Electrical Engineering is a collection of seven labs that demonstrate how the Analog Discovery 2 can provide a way for students to experiment at home. The labs included are: RC...
Bipolar Junction Transistors

In this lab students will be looking at applications of transistors in the real world, learning about their importance, use, and applications. Designed for use with NI ELVIS III.
Project - FM Radio Tuner

In this lab, students will apply their knowledge of circuits and hands-on concepts to understand components of a complex real-world device: a radio. Designed for use with NI ELVIS III.
Transistor Amplifiers

In this lab students will examine the implementation of amplifiers using transistors and identify their characteristics and applications. Designed for use with NI ELVIS III.
RLC Circuits

In this lab, students will learn about RLC circuits and how to calculate their different parts, and then finally how to build them on a bread board. Designed for use with NI ELVIS III.
Linear Regulator in Open Loop DC Operation

by Dr. Nicola Femia | University of Salerno, and Texas Instruments

Students investigate the properties of a MOSFET in DC operation when it works as a pass device in linear regulators. Designed for NI ELVIS III.
Lab 1: RC Circuits

by National Instruments

This lab covers the basic characteristics of RC Circuits, including both DC and AC analysis, simulation, and experimentation.
Lab 2: Active and Passive Filters

by National Instruments

This lab introduces students to filter transfer functions for passive and active filters and allows them to apply their knowledge by simulating and building these circuits.
Transformers and Turn Relationships

In this lab students will learn about transformers by working with two different simulations and hands-on applications with circuits. Designed for use with NI ELVIS III.
Op-Amps Amplifiers

In this lab students measure the response of an op-amp commonly used in closed-loop configurations through hands-on and web-based applications. Designed for use with NI ELVIS III.
ECE Fundamentals 1

by The University of Virginia

Developed in collaboration with the University of Virginia, Fundamentals 1 is the first in a series of 3 course sets that redefine how the core topics of circuits, electronics, and signals and...
Logic Gates Explored and Boolean Algebra

Students explore basic logic gates, boolean algebra, and deriiving cominational logic circuits using circuit simulation and PLD deployment. Designed for NI ELVIS III.
Electronics 102

Electronics 102 is an online, interactive course covering basic analog electronics components such as diodes, transistors, and operational amplifiers. Designed for NI ELVIS II/II+.
Electronic Safe Project

by Enable Education

Students will use concepts and skills they developed in previous labs on combination logic to design and build an electronic safe with a 4-digit password. Designed for NI ELVIS III.
Binary Conversion and Adders

In this lab, students use Mulitisim to simulate different methods of binary addition, complete analysis, and validate circuits simulations on an FPGA. Designed for NI ELVIS III.
Comparators

In this lab, students will simulate comparitor circuits and deploy them to an FPGA. Designed for NI ELVIS III.