Table Of Contents

Specifications

Version:
    Last Modified: May 11, 2017

    This document lists specifications for the NI-5793 adapter module. Pair these specifications with the specifications listed in your FlexRIO FPGA module specifications document or your Controller for FlexRIO specifications document. Specifications are warranted by design and under the following conditions unless otherwise noted.

    • Chassis fan speed is set to High. In addition, NI recommends using slot blockers and EMC filler panels in empty module slots to minimize temperature drift.
    • The NI-5793 uses NI LabVIEW and LabVIEW FPGA software.

    National Instruments RF devices are capable of acquiring and/or generating signals within common Medical Implantable Communication System (MICS) frequency bands. NI RF devices are tested and verified in manufacturing for several measurements. For more information about RF device applications, contact a National Instruments branch office.

    spd-note-caution
    Caution  

    To avoid permanent damage to the NI-5793, disconnect all signals connected to the NI-5793 before powering down the module, and only connect signals after the module has been powered on by the FlexRIO FPGA module or the Controller for FlexRIO.

    Specifications are subject to change without notice. For the most recent device specifications, visit ni.com/manuals.

    Definitions

    Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.

    Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.

    • Typical specifications describe the expected performance met by a majority of the models.
    • Nominal specifications describe parameters and attributes that may be useful in operation.

    Specifications are Typical unless otherwise noted.

    TX OUT

    Amplitude Characteristics

    Power range

    Output

    Noise floor to +8 dBm, nominal

    Output resolution

    0.25 dB, nominal

    Amplitude settling time

    <0.5 dB within 1 ms, nominal

    Absolute Amplitude Accuracy

    spd-note-note
    Note  

    All values are typical.

    spd-note-note
    Note  

    Absolute amplitude accuracy uses a correction coefficient in EEPROM to improve performance. The TX amplitude accuracy applies to the output power level from -12 dBm to -4 dBm.

    Table 1. Transmit Absolute Amplitude Accuracy
    Frequency Temperature 23 °C ±5 °C (dB)
    >200 MHz to 1 GHz 0.8
    1 GHz to 2 GHz 1.3
    2 GHz to 3 GHz 1.3
    3 GHz to 4.4 GHz 1.8
    Figure 1. TX Output Power

    Noise Density

    spd-note-note
    Note  

    All values are typical.

    spd-note-note
    Note  

    Performance is measured with 0 dB of TX attenuation.

    Frequency Temperature 23 °C ±5 °C (dBm/Hz)
    >200 MHz to 1 GHz -138
    >1 GHz to 2 GHz -138
    >2 GHz to 4.4 GHz -138

    Output Voltage Standing Wave Ratio (VSWR)

    <2.0 GHz

    1.6:1

    ≥2.0 GHz and <3.0 GHz

    1.4:1

    ≥3.0 GHz

    1.7:1

    spd-note-note
    Note  

    The VSWR is measured with 10 dB of TX attenuation.

    TX OUT Third Order Intermodulation (IP3)

    spd-note-note
    Note  

    All values are typical.

    spd-note-note
    Note  

    Values are based on two input tones spaced 1.3 MHz apart with 5 dB of TX attenuation.

    Table 2. TX IP 3
    Frequency Temperature 23 °C ± 5 °C (dBm)
    >200 MHz to 1 GHz 19
    >1 GHz to 2 GHz 17
    >2 GHz to 3 GHz 13
    >3 GHz to 3.9 GHz 11
    >3.9 GHz to 4.4 GHz 8

    Second Order Intermodulation (IP2)

    spd-note-note
    Note  

    All values are typical.

    Table 3. IP 2
    Frequency Temperature 23 °C ±5 °C (dBm)
    >200 MHz to 1 GHz 25
    >1 GHz to 2 GHz 25
    >2 GHz to 3 GHz 25
    >3 GHz to 4.4 GHz 35
    spd-note-note
    Note  

    Values are based on two input tones spaced 1.3 MHz MHz apart with 5 dB of TX attenuation.

    TX Sideband Image Suppression

    spd-note-note
    Note  

    All values are nominal.

    Table 4. Image Suppression
    Frequency Temperature 23 °C ±5 °C (dBc)
    >200 MHz to 1 GHz -50
    >1 GHz to 2 GHz -50
    >2 GHz to 3 GHz -50
    >3 GHz to 4.4 GHz -45
    spd-note-note
    Note  

    The image suppression specifications hold at the center frequency of the transmitted instantaneous bandwidth after the device performs a recent single point I/Q impairment self-correction.

    TX LO Residual Power

    spd-note-note
    Note  

    All values are typical.

    Table 5. TX LO Residual Power
    Frequency Temperature 23 °C ±5 °C (dBm)
    >200 MHz to 1 GHz -48
    >1 GHz to 2 GHz -48
    >2 GHz to 3 GHz -48
    >3 GHz to 4.4 GHz -45
    spd-note-note
    Note  

    This specification holds at the center frequency of the transmitted instantaneous bandwidth, 100 MHz maximum after the device performs a recent single point I/Q impairment self-correction. The measurement is performed with 0 dB of TX attenuation.

    LO OUT Front Panel Connector

    Frequency range

    200 MHz to 4.4 GHz

    Power

    3 dBm, ±3 dB, nominal

    Output power resolution

    0.15 dB

    Output impedance

    50 Ω, nominal

    Output VSWR

    1.78:1

    Amplitude settling time

    < 0.25 dB in less than 10 ms, typical

    Maximum DC voltage

    ±0.5 VDC

    Figure 2. LO Output Power vs. LO Frequency

    LO IN Front Panel Connector

    Frequency range

    200 MHz to 4.4 GHz

    Input power

    3 dBm ±3 dB, nominal

    Input impedance

    50 Ω

    Input VSWR

    1.78:1

    Absolute maximum power

    +15 dBm

    Maximum DC power

    ±0.5 VDC

    TX OUT Frequency Characteristics

    Frequency range

    200 MHz to 4.4 GHz

    Instantaneous bandwidth (6 dB)

    200 MHz[1]

    Tuning resolution[2]

    <250 kHz

    LO step size[3]

    Integer mode

    4 MHz, 6 MHz, 12 MHz, 24 MHz

    Fractional mode

    100 kHz step size

    Figure 3. TX OUT Frequency Response

    Frequency Settling Time

    Settling time[4]

    < 50 ms per 100 MHz step

    Phase Noise

    spd-note-note
    Note  

    All values are nominal.

    Table 6. Phase Noise at 2.4 GHz
    Offset Frequency Loop Phase Noise (dBc/Hz)
    1 kHz -85
    10 kHz -95
    100 kHz -97
    1 MHz -100
    10 MHz -110
    Figure 4. Phase Noise

    Baseband Characteristics

    Digital-to-Analog Converters (DAC)[5]

    Part number

    TI DAC 3482

    Resolution

    16 bits

    Data rate

    250 MS/s

    I/Q data rate

    1.84 kS/s to 250 MS/s[6]

    CLK IN Front Panel Connector

    Frequency

    Reference Clock

    10 MHz

    Sample Clock

    250 MHz

    Amplitude

    Square

    0.7 Vpk-pk to 5.0 Vpk-pk into 50 Ω, typical

    Sine

    1.4 Vpk-pk to 5.0 Vpk-pk (1 VRMS to 3.5 VRMS) into 50 Ω, typical

    Input impedance

    50 Ω, nominal

    Coupling

    AC

    CLK OUT Front Panel Connector

    Interface standard

    3.3 V LVCMOS

    Interface logic

    Maximum VOL

    0.55 V

    Minimum VOH

    2.7 V

    Maximum VOH

    3.6 V

    Output impedance

    50 Ω ±20%

    Coupling

    DC

    Iout (DC)

    ±32 mA

    Dimensions and Weight

    Dimensions

    12.9 × 2.0 × 12.1 cm (5.1 × 0.8 × 4.7 in)

    Weight

    413 g (14.6 oz)

    I/O

    RX in, RX out, LO in, LO out, 10 MHz, 10 MHz out

    Power

    6 W, nominal, with one LO turned on

    AUX I/O Connector

    Table 7. NI-5793 AUX I/O Connector Pin Assignments
    AUX I/O Connector Pin Signal Signal Description
    1 DIO Port 0 (0) Bidirectional single-ended (SE) digital I/O (DIO) data channel.
    2 GND Ground reference for signals.
    3 DIO Port 0 (1) Bidirectional SE DIO data channel.
    4 DIO Port 0 (2) Bidirectional SE DIO data channel.
    5 GND Ground reference for signals.
    6 DIO Port 0 (3) Bidirectional SE DIO data channel.
    7 DIO Port 1 (0) Bidirectional SE DIO data channel.
    8 GND Ground reference for signals.
    9 DIO Port 1 (1) Bidirectional SE DIO data channel.
    10 DIO Port 1 (2) Bidirectional SE DIO data channel.
    11 GND Ground reference for signals.
    12 DIO Port 1 (3) Bidirectional SE DIO data channel.
    13 PFI 0 Bidirectional SE DIO data channel.
    14 NC No connect.
    15 PFI 1 Bidirectional SE DIO data channel.
    16 PFI 2 Bidirectional SE DIO data channel.
    17 GND Ground reference for signals.
    18 +5 V +5 V power (10 mA maximum).
    19 PFI 3 Bidirectional SE DIO data channel.
    spd-note-caution
    Caution  

    The AUX I/O connector accepts a standard, third-party HDMI cable, but the AUX I/O port is not an HDMI interface. Do not connect the AUX I/O port on the NI-5793 to the HDMI port of another device. NI is not liable for any damage resulting from such signal connections.

    AUX I/O (Port 0 DIO <0..3>, Port 1 DIO <0..3>, and PFI <0..3>

    Number of channels

    12 bidirectional (8 DIO and 4 PFI)

    Connector type

    HDMI

    Interface standard

    3.3 V LVCMOS

    Interface logic

    Maximum VIL

    0.8 V

    Minimum VIH

    2.0 V

    Maximum VOL

    0.4 V

    Minimum VOH

    2.7 V

    Maximum VOH

    3.6 V

    Zout

    50 Ω ± 20%

    Iout (DC)

    ±2 mA

    Pull-down resistor

    150 kΩ

    Recommended operating voltage

    -0.3 V to 3.6 V

    Overvoltage protection

    ±10 V

    Maximum toggle frequency

    6.6 MHz

    +5 V maximum power

    10 mA

    +5 V voltage tolerance

    4.2 V to 5 V

    Environment

    Maximum altitude

    2,000 m (800 mbar) (at 25 °C ambient temperature)

    Pollution Degree

    2

    Indoor use only.

    Operating Environment

    Ambient temperature range

    0 °C to 55 °C (Tested in accordance with IEC 60068-2-1 and IEC 60068-2-2. Meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 2 high temperature limit.)

    Relative humidity range

    10% to 90%, noncondensing (Tested in accordance with IEC 60068-2-56.)

    Storage Environment

    Ambient temperature range

    -20 °C to 70 °C (Tested in accordance with IEC 60068-2-1 and IEC 60068-2-2. Meets MIL-PRF-28800F Class 3 limits.)

    Relative humidity range

    5% to 95%, noncondensing (Tested in accordance with IEC 60068-2-56.)

    Shock and Vibration

    Operating shock

    30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC 60068-2-27. Meets MIL-PRF-28800F Class 2 limits.)

    Random vibration

    Operating

    5 Hz to 500 Hz, 0.3 grms (Tested in accordance with IEC 60068-2-64.)

    Nonoperating

    5 Hz to 500 Hz, 2.4 grms (Tested in accordance with IEC 60068-2-64. Test profile exceeds the requirements of MIL-PRF-28800F, Class 3.)

    Compliance and Certifications

    Safety

    This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA C22.2 No. 61010-1
    spd-note-note
    Note  

    For UL and other safety certifications, refer to the product label or the Online Product Certification section.

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:
    • EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • EN 55022 (CISPR 22): Class A emissions
    • EN 55024 (CISPR 24): Immunity
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • AS/NZS CISPR 22: Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions
    spd-note-note
    Note  

    In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended for use only in heavy-industrial locations.

    spd-note-note
    Note  

    Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.

    spd-note-note
    Note  

    For EMC declarations, certifications, and additional information, refer to the Online Product Certification section.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:

    • 2014/35/EU; Low-Voltage Directive (safety)
    • 2014/30/EU; Electromagnetic Compatibility Directive (EMC)

    Online Product Certification

    Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

    For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)

    spd-note-weee
    EU Customers  

    At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.

    电子信息产品污染控制管理办法(中国RoHS)

    spd-note-china-rohs
    中国客户  

    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

    Worldwide Support and Services

    The NI website is your complete resource for technical support. At ni.com/support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers.

    Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and other services.

    Visit ni.com/register to register your NI product. Product registration facilitates technical support and ensures that you receive important information updates from NI.

    A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity. This system affords the user protection for electromagnetic compatibility (EMC) and product safety. You can obtain the DoC for your product by visiting ni.com/certification. If your product supports calibration, you can obtain the calibration certificate for your product at ni.com/calibration.

    NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. NI also has offices located around the world. For telephone support in the United States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the Worldwide Offices section of ni.com/niglobal to access the branch office websites, which provide up-to-date contact information, support phone numbers, email addresses, and current events.

    • 1 Instantaneous bandwidth is 200 MHz at 6 dB. Instantaneous bandwidth is 130 MHz at 3 dB.
    • 2 Tuning resolution combines LO step size capability and frequency shift DSP implemented on the FPGA.
    • 3 All LO step size specifications are assumed to be with fractional mode enabled and a 100 kHz LO step size.
    • 4 The settling time specification only includes frequency settling, and it excludes any residual amplitude settling that may occur as a result of large frequency changes. Driver and operating system timing can affect transition times. This specification reflects only hardware settling.
    • 5 DACs are dual-channel components with each channel assigned to I and Q, respectively.
    • 6 The NI 5793 interpolates the data rate using Fractional Interpolation DSP blocks implemented in the LabVIEW FPGA target. See <resource here> for information about how to use Frequency Shift DSP blocks.

    Recently Viewed Topics