Table Of Contents

stPMU Disable PMU (G Dataflow)

Version:
    Last Modified: September 29, 2017

    Disables the PMU source operations on the channels specified in the channel list parameter. Use the return state parameter to tristate or return each channel to its previous digital state.

    spd-note-note
    Note  

    When you use the PMU nodes to source a voltage or current on your system, the voltage or current continues to be sourced on the selected channels until you reset your device or call this node. The Abort and Close nodes do not stop sourcing the voltage or current.

    spd-note-note
    Note  

    Even after using this node to disable the PMU source operations, you can still use the PMU measure voltage operations.

    spd-note-note
    Note  

    Only the PXIe-6555 and the PXIe-6556 support this node.

    connector_pane_image
    datatype_icon

    session in

    Instrument session obtained from the Initialize Acquisition Session node, the Initialize Generation Session node, or the Initialize External Calibration node.

    datatype_icon

    channel list

    The channels you want to configure.

    Specify multiple channels by using a channel list or a channel range. A channel list is a comma (,) separated sequence of channel names (for example, 0,2 specifies channels 0 and 2). A channel range is a lower bound channel followed by a hyphen (-) or colon (:) followed by an upper bound channel (for example, 0-2 specifies channels 0, 1, and 2).

    Use PFI1 or PFI2 to specify a valid PFI channel. Use DDC_CLKOUT or STROBE to specify a valid clocking terminal. If you configure multiple channels with this parameter, all those channels have the same settings. Selecting no channels for this parameter returns an error.

    datatype_icon

    return state

    Parameter that selects, after disabling, whether to tristate the channel or to return it to its previous digital state.

    spd-note-note
    Note  

    PFI 1, PFI 2, DDC CLK OUT, and STROBE support only previous digital state. If you try to tristate a PFI channel, NI-HSDIO returns an error.

    Name Description
    Tristate

    Tristates the channel.

    Previous digital state

    Returns the channel to its previous digital state.

    Default: Tristate

    datatype_icon

    error in

    Error conditions that occur before this node runs.

    The node responds to this input according to standard error behavior.

    Standard Error Behavior

    Many nodes provide an error in input and an error out output so that the node can respond to and communicate errors that occur while code is running. The value of error in specifies whether an error occurred before the node runs. Most nodes respond to values of error in in a standard, predictable way.

    error in does not contain an error error in contains an error
    If no error occurred before the node runs, the node begins execution normally.

    If no error occurs while the node runs, it returns no error. If an error does occur while the node runs, it returns that error information as error out.

    If an error occurred before the node runs, the node does not execute. Instead, it returns the error in value as error out.

    Default: No error

    datatype_icon

    session out

    Handle that identifies the session in all subsequent node calls.

    The session out parameter is obtained from the Initialize Acquisition Session node or the Initialize Generation Session node.

    datatype_icon

    error out

    Error information.

    The node produces this output according to standard error behavior.

    Standard Error Behavior

    Many nodes provide an error in input and an error out output so that the node can respond to and communicate errors that occur while code is running. The value of error in specifies whether an error occurred before the node runs. Most nodes respond to values of error in in a standard, predictable way.

    error in does not contain an error error in contains an error
    If no error occurred before the node runs, the node begins execution normally.

    If no error occurs while the node runs, it returns no error. If an error does occur while the node runs, it returns that error information as error out.

    If an error occurred before the node runs, the node does not execute. Instead, it returns the error in value as error out.

    Committing your session

    If you have not yet committed your session, calling this node implicitly commits your session. If you have already committed your session by calling a node such as the Commit node, the Initiate node, the Read Waveform node, the Write Named Waveform node, or the other nodes, this node will not commit your session again.

    Where This Node Can Run:

    Desktop OS: Windows

    FPGA: Not supported

    Web Server: Not supported in VIs that run in a web application


    Recently Viewed Topics