Table Of Contents

MT Generate System Parameters (MT Generate CPM System Parameters (M)) (G Dataflow)

Version:
    Last Modified: February 7, 2018

    Accepts an M-ary value that specifies a predefined symbol map with the number of distinct symbol map values to use as symbols.

    connector_pane_image
    datatype_icon

    samples per symbol

    Number of samples dedicated to each symbol. Multiply this value by the symbol rate to determine the sample rate.

    Default: 16

    datatype_icon

    M-CPM

    The M-ary number, which is the number of distinct frequency deviations to use as symbols. This value must be a positive power of 2.

    Default: 2

    datatype_icon

    modulation index, h(i)

    Modulation index for the CPM modulation scheme.

    Refer to CPM Modulation for more information about modulation indices. The modulation index must be of proper form, that is, the numerator must be lesser than the denominator. The modulation index may vary between symbol intervals.

    datatype_icon

    numerator

    Numerator of the modulation index.

    datatype_icon

    denominator

    Denominator of the modulation index.

    datatype_icon

    symbol rate

    The desired symbol rate, in hertz (Hz).

    Default: 1.0

    datatype_icon

    error in

    Error conditions that occur before this node runs.

    The node responds to this input according to standard error behavior.

    Standard Error Behavior

    Many nodes provide an error in input and an error out output so that the node can respond to and communicate errors that occur while code is running. The value of error in specifies whether an error occurred before the node runs. Most nodes respond to values of error in in a standard, predictable way.

    error in does not contain an error error in contains an error
    If no error occurred before the node runs, the node begins execution normally.

    If no error occurs while the node runs, it returns no error. If an error does occur while the node runs, it returns that error information as error out.

    If an error occurred before the node runs, the node does not execute. Instead, it returns the error in value as error out.

    Default: No error

    datatype_icon

    CPM system parameters

    Parameter values defining the CPM system. Wire this parameter to the corresponding system parameters cluster of MT Modulate CPM, MT Demodulate CPM, or MT Detect CPM.

    datatype_icon

    samples per symbol

    Number of samples dedicated to each symbol. Multiply this value by the symbol rate to determine the sample rate.

    datatype_icon

    symbol map

    A two-dimensional array of desired frequency deviations. Each column corresponds to a symbol, with the binary representation of the column index being the mapped bit-representation of the symbol. Each row corresponds to a modulation index in the order in which it appears in the modulation index, h(i) parameter of MT Generate CPM System Parameters (M) or MT Generate CPM System Parameters (map).

    Default: Empty array

    datatype_icon

    bits per symbol

    Number of bits represented by each symbol. This value is equal to Log 2 (M), where M is the order of the modulation (for example, for 4-CPM, M = 4).

    datatype_icon

    error out

    Error information.

    The node produces this output according to standard error behavior.

    Standard Error Behavior

    Many nodes provide an error in input and an error out output so that the node can respond to and communicate errors that occur while code is running. The value of error in specifies whether an error occurred before the node runs. Most nodes respond to values of error in in a standard, predictable way.

    error in does not contain an error error in contains an error
    If no error occurred before the node runs, the node begins execution normally.

    If no error occurs while the node runs, it returns no error. If an error does occur while the node runs, it returns that error information as error out.

    If an error occurred before the node runs, the node does not execute. Instead, it returns the error in value as error out.

    Where This Node Can Run:

    Desktop OS: Windows

    FPGA: Not supported

    Web Server: Not supported in VIs that run in a web application


    Recently Viewed Topics