Table Of Contents

SWB-2815A/B Specifications

Version:
    Last Modified: April 21, 2017

    This document lists specifications for the SWB-2815A/B matrix relay card. All specifications are subject to change without notice. Visit ni.com/manuals for the most current specifications. Refer to the NI Switches Help for detailed topology information.

    Topology

    1-wire 4 × 86 matrix

    About These Specifications

    Specifications characterize the warranted performance of the instrument under the stated operating conditions.

    Typical Specifications are specifications met by the majority of the instrument under the stated operating conditions and are tested at 23 °C ambient temperature. Typical specifications are not warranted.

    All voltages are specified in DC, ACpk, or a combination unless otherwise specified.

    Clean devices and terminal blocks by brushing off light dust with a soft, nonmetallic brush. Remove other contaminants with a soft, lint-free, dampened cloth. Do not use detergent or chemical solvents. The unit must be completely dry and free from contaminants before returning to service.

    Cautions

    spd-note-caution
    Caution  

    This module is rated for Measurement Category I and intended to carry signal voltages no greater than 70 Vrms/100 Vpk/100 VDC. This module can withstand up to 500 V impulse voltage. Do not use this module for connection to signals or for measurements within Categories II, III, or IV. Do not connect to MAINS supply circuits (for example, wall outlets) of 115 VAC or 230 VAC. Refer to the Read Me First: Safety and Electromagnetic Compatibility document for more information on measurement categories.

    spd-note-caution
    Caution  

    Measurement Categories CAT I and CAT O are equivalent. These test and measurement circuits are not intended for direct connection to the MAINs building installations of Measurement Categories CAT II, CAT III, or CAT IV.

    spd-note-caution
    Caution  

    In systems that include cards with different maximum voltages, the lowest safety voltage rating as specified on the front of the card applies for the entire system. The system can include all cards in the carrier, and all cards in other carriers that are connected with the NI 2806 expansion bridge.

    spd-note-caution
    Caution  

    When hazardous voltages (>42.4 Vpk/60 VDC) are present on any channel, safety low-voltage (≤42.4 Vpk/60 VDC) cannot be connected to any other channel.

    spd-note-caution
    Caution  

    Refer to the Read Me First: Safety and Electromagnetic Compatibility document for important safety and electromagnetic compatibility information. To obtain a copy of this document online, visit ni.com/manuals, and search for the document title.

    spd-note-caution
    Caution  

    To ensure the specified EMC performance, operate this product only with shielded cables and accessories.

    spd-note-caution
    Caution  

    The protection provided by the SWB-2815A/B can be impaired if it is used in a manner not described in this document.

    spd-note-caution
    Caution  

    Always disconnect or turn off power sources before powering on a chassis.

    Input Characteristics

    Maximum switching voltage

    Row/column-to-ground

    100 V, CAT I

    Row-to-column

    100 VDC/70 VAC

    Maximum switching current

    0.25 A (per channel)

    Maximum carry current

    0.3 A (per channel)

    Maximum switching power

    Per channel

    3 W

    Per crosspoint

    3 W

    DC path resistance

    Initial

    <1 Ω

    End-of-life

    ≥2 Ω

    Open channel

    >1 × 109 Ω

    spd-note-note
    Note  

    DC path resistance typically remains low for the life of the relay. At the end of relay life, the path resistance rises rapidly above the specified value. Load ratings apply to relays used within the specification before the end of relay life.

    Thermal EMF, typical

    <50 μV

    Bandwidth, typical (-3 dB, 50 Ω termination, column-row-column)

    ≥6 MHz

    Crosstalk, typical (50 Ω termination) channel-to-channel

    10 kHz

    <-60 dB

    100 kHz

    <-50 dB

    1 MHz

    <-30 dB

    Isolation, typical (50 Ω termination) open channel

    10 kHz

    >65 dB

    100 kHz

    >50 dB

    1 MHz

    >30 dB

    Analog bus line connections

    AB <0...3> (4 Lines)

    Peak Switching Voltage Versus Current

    The following figure shows the peak switching voltage in relation to the peak switching current.

    Figure 1. Peak Switching Voltage Versus Current

    Dynamic Characteristics

    Simultaneous drive limit[1]

    61 relays

    Relay operate/release time (simultaneous relays), typical[2]

    Up to 8 relays

    <1 ms

    Up to 50 relays

    <2 ms

    Expected relay life, mechanical (no load)

    2.5 × 108 cycles

    Expected relay life, electrical (resistive, <10 pF load)

    5 V, 10 mA

    1 × 109 cycles

    10 V, 100 mA

    4 × 106 cycles

    100 V, 10 mA

    5 × 105 cycles

    spd-note-note
    Note  

    Optional 100 Ω series protection resistance, available for the interface cable, increases the expected relay life at higher voltages by protecting the reed relays from the effects of cable and load capacitance. For more information about increasing the life of your relay, visit ni.com/info and enter the Info Code relaylifetime.

    spd-note-note
    Note  

    Reed relays are highly susceptible to damage caused by switching capacitive and inductive loads. Capacitive loads can cause high inrush currents, and inductive loads can cause high flyback voltages. The addition of appropriate protection can greatly improve contact lifetime. For more information about adding protection circuitry to a capacitive load, visit ni.com/info and enter the Info Code relaylifetime. For information about inductive loads, enter the Info Code relayflyback.

    Power

    Power consumption per relay

    63 mW

    Power consumption limit[3]

    3.9 W

    Power dissipation limit

    Card

    3.9 W

    Carrier

    3.9 W

    Physical Characteristics

    Relay type

    Reed

    Relay contact material

    Ruthenium

    I/O connectors

    96 position, plastic SCSI

    Power requirement, carrier

    10 W at 5 V, 2 W at 3.3 V

    Dimensions (L × W × H)

    11.2 cm × 1.2 cm × 17.1 cm (4.4 in. × 0.5 in. × 6.7 in.)

    Weight

    320 g (11.3 oz)

    Environment

    Maximum altitude

    2,000 m (at 25 °C ambient temperature)

    Pollution Degree

    2

    Indoor use only.

    Operating Environment

    Ambient temperature range

    0 °C to 55 °C (Tested in accordance with IEC-60068-2-1 and IEC-60068-2-2.)

    Relative humidity range

    10% to 90%, noncondensing (Tested in accordance with IEC-60068-2-56.)

    Storage Environment

    Ambient temperature range

    -20 °C to 70 °C (Tested in accordance with IEC-60068-2-1 and IEC-60068-2-2.)

    Relative humidity range

    5% to 95%, noncondensing (Tested in accordance with IEC-60068-2-56.)

    Operational shock

    30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC-60068-2-27. Test profile developed in accordance with MIL-PRF-28800F.)

    Random vibration

    Operating

    5 Hz to 500 Hz, 0.3 grms

    Nonoperating

    5 Hz to 500 Hz, 2.4 grms (Tested in accordance with IEC-60068-2-64. Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.)

    Compliance and Certifications

    Safety

    This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:
    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA 61010-1
    spd-note-note
    Note  

    For UL and other safety certifications, refer to the product label or the Online Product Certification section.

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:
    • EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions
    spd-note-note
    Note  

    In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended for use only in heavy-industrial locations.

    spd-note-note
    Note  

    Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.

    spd-note-note
    Note  

    For EMC declarations, certifications, and additional information, refer to the Online Product Certification section.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:
    • 2006/95/EC; Low-Voltage Directive (safety)
    • 2004/108/EC; Electromagnetic Compatibility Directive (EMC)

    Online Product Certification

    To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial not only to the environment but also to NI customers.

    For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)
    spd-note-weee
    EU Customers  

    At the end of the product life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste Electrical and Electronic Equipment, visit ni.com/environment/weee.htm.

    电子信息产品污染控制管理办法(中国RoHS)
    spd-note-china-rohs
    中国客户  

    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

    Accessories

    Refer to ni.com for more information about the following accessories.

    spd-note-caution
    Caution  

    Use only NI cables. Cables with metal connectors might expose the user to hazardous voltages.

    spd-note-note
    Note  

    To ensure the specified EMC performance, operate this product only with shielded cables and accessories. Do not use unshielded cables or accessories unless they are installed in a shielded enclosure with properly designed and shielded input/output ports and are connected to the NI product using a shielded cable. If unshielded cables or accessories are not properly installed and shielded, the EMC specifications for the product are no longer guaranteed.

    Table 1. NI Accessories for the SWB-2815A/B
    Accessory Part number
    SH96F-96M-NI SwitchBlock Cable 150275-01
    SH96F-96M-RES-NI SwitchBlock Cable with 100 Ω resistance 150579-01
    NI TBX-2809 Screw Terminal Accessory (unshielded) 781420-09
    • 1 The overall carrier drive limit prevents simultaneous drive of relays under the card limit on some cards in some configurations. Refer to the NI 2800 Specifications for information about carrier drive limit.
    • 2 Relay operate and release times depend on PC and PXI bus performance and application software. For more information about NI SwitchBlock relay operate times, visit ni.com/info and enter the Info Code exa9ee.
    • 3 For more information about NI SwitchBlock power limits, visit ni.com/info and enter the Info Code sbpwrlim.

    Recently Viewed Topics