Demodulates a phase-shift keying (PSK)-modulated complex baseband waveform and returns the demodulated bit stream. This node attempts to remove carrier and phase offset by locking to the carrier signal.

The modulated complex baseband waveform data.

Trigger (start) time of the **Y** array.

**Default: **0.0

Time interval between data points in the **Y** array.

**Default: **1.0

The complex-valued signal-only baseband modulated waveform. The real and imaginary parts of this complex data array correspond to the in-phase (I) and quadrature-phase (Q) data, respectively.

Parameter values defining the PSK system. Wire the **PSK system parameters** cluster of MT Generate PSK System Parameters (M) or MT Generate PSK System Parameters (map) to this cluster. Do not alter the values.

An ordered array that maps each Boolean symbol to its desired coordinates in the complex plane. The number of states in the array must be 2^{ N }, where *N* is the number of bits per symbol.

Status of the differential PSK.

disable | Disables bit sequence encoding. |

enable | Enables bit sequence encoding. |

**Default: ****enable**

Type of PSK modulation.

normal | Sets the modulation type to regular PSK. |

shifted | Rotates the constellation by $\pi $/M each symbol. |

offset | Sets the modulation type to offset quadrature phase-shift keying (OQPSK). This modulation scheme is a form of phase-shift keying in which four different phase angles are used. This scheme is sometimes referred to as staggered quadrature phase-shift keying (SQPSK). For offset PSK, the ideal symbol timing for Q is offset by 1/2 of a symbol period from the ideal symbol timing for I. |

**Default: ****normal**

Parameter values describing the synchronization sequence and the range of bits over which to search for this sequence. Wire the **PSK synchronization parameters** cluster returned by the PSK bit array or number array instances of MT Generate Synchronization Parameters to this cluster.

The expected location of the first symbol of the **sync sequence**.

This value is an index to the **input complex waveform**. A value of -1 searches the entire **input complex waveform** and ignores the **sync location uncertainty** parameter.

The mapped symbol pattern used to synchronize the bit stream. To prevent false synchronization, select this pattern such that there is a low probability of accidental correlation to nonsynchronized parts of the data stream. If this parameter is left empty, the signal is still demodulated, but there is a phase ambiguity in the recovered symbols.

Number of symbols before or after the **expected sync location** where the first symbol of the **sync sequence** may be located. The node ignores this parameter if the **expected sync location** parameter is set to -1.

**Default: **10

Distance that the **sync sequence** is indented into the information block.

The distance is the number of demodulated symbols preceding the **sync sequence**. For example, a value of 10 indicates that the **output bit stream** consists of 10 data symbols, followed by the **sync sequence**, followed by the remaining data symbols.

**Default: **0

Error conditions that occur before this node runs. The node responds to this input according to standard error behavior.

**Default: **no error

An ordered array containing the desired matched filter coefficients. Wire the **matched filter coefficients** parameter of MT Generate Filter Coefficients to this parameter. When generating the filter coefficients, ensure that the value of the **matched samples per symbol** parameter of MT Generate Filter Coefficients is equal to the value of the **samples per symbol** element of the **PSK system parameters** cluster passed to this node.

Dependency on reset? Input

When **reset?** is set to TRUE, there is a transient response of half the filter length at the start of the demodulated signal, and the returned data is shortened by approximately half the filter length. When **reset?** is set to FALSE, the node uses data from the previous iteration to eliminate the transient.

When **reset?** is set to TRUE, the number of trailing symbols that are carried over to the next iteration during demodulation is upper bounded by [*L* + 4(13 + *K*)]/*K* , where *L* is the matched filter length in taps and *K* is the number of samples per symbol. For typical values of *L* = 25 (4 samples per symbol, filter length of 6 symbols) and *K* = 4, this value equals 23.25 symbols. Therefore when **reset?** is set to TRUE, a total of 1,024 PSK symbols must be passed to the demodulator to obtain at least 1,000 symbols at the output. This formula does not account for truncation due to any specified **synchronization parameters**.

A Boolean that determines whether the node continues demodulating using the previous iteration states.

TRUE | Restarts the demodulator. The node resets on the first call and when reset? is set to TRUE. |

FALSE | Continues demodulating using the previous iteration states. The input complex waveform is contiguous with the input complex waveform from the previous iteration of this node. |

**Default: **TRUE

A Boolean that determines whether to flush samples from the **input complex waveform** that are delayed due to the FIR filters used in the demodulation algorithm. Set this parameter to TRUE during single-shot operations and during the last iteration of continuous operations.

TRUE | Destroys the internal states of the algorithms such that you cannot perform continuous processing on the signal during subsequent iterations. If flush buffers? is set to TRUE, you must set reset? to TRUE on the subsequent iteration. |

FALSE | Stores the internal states of the algorithms so that you can perform continuous processing on the signal during subsequent iterations. |

**Default: **FALSE

Symbol index within the **input complex waveform** where the peak correlation to the **sync sequence** was found. If no **sync sequence** is specified in the **synchronization parameters** cluster, the **sync found index** parameter returns the offset from the start of the **input complex waveform** to the first complete symbol.

Error information. The node produces this output according to standard error behavior.

Offset PSK mode is only supported for 4-PSK (OQPSK), and setting **psk type** to **offset** requires some form of band-limiting filtration. Raised cosine and root-raised cosine are the only valid filter types for OQPSK demodulation. Demodulator locking performance degrades with alpha values <0.3 in the raised cosine or root-raised cosine filter design. Set the **PSK type** parameter to **offset** in MT Generate PSK System Parameters (M) or MT Generate PSK System Parameters (Map) to access this mode.

Successful locking depends on many factors, including signal quality, modulation type, filtering parameters, and acquisition size. Locking also requires a fairly uniform distribution of symbols in the signal. The demodulator lock rate increases (and failures decrease) as the number of symbols demodulated increases. In general, you can expect to achieve a better than 95% lock when demodulating 10 × *M* number of symbols, where *M* is 2^{ bits per symbol }.

**Installed By: **LabVIEW Communications System Design Suite (introduced in 1.0)

**Where This Node Can Run: **

Desktop OS: Windows

FPGA: Not supported