Table Of Contents

NI-5771 Specifications

Version:
    Last Modified: January 12, 2017

    This document lists specifications for the NI-5771. All specifications are subject to change without notice.

    spd-note-caution
    Caution  

    The protection provided by the NI-5771 can be impaired if it is used in a manner not described in this document.

    spd-note-caution
    Caution  

    To avoid permanent damage to the NI-5771, disconnect all signals connected to the NI-5771 before powering down the module, and only connect signals after the module has been powered on by the FlexRIO FPGA module or the Controller for FlexRIO.

    Specifications are subject to change without notice. For the most recent device specifications, visit ni.com/manuals.

    Definitions

    Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.

    Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.

    • Typical specifications describe the expected performance met by a majority of the models.
    • Nominal specifications describe parameters and attributes that may be useful in operation.

    Specifications are Typical unless otherwise noted.

    Analog Input (AI 0 and AI 1)

    General Characteristics

    Number of channels

    Two

    Connector type

    SMA

    Input type

    Simultaneously sampled, single-ended

    Input impedance

    50 Ω, per connector

    Input coupling

    DC

    Signal paths

    Lattice filter

    Digital data resolution

    8-bit, unsigned, binary data

    ADC

    ADC08D1520[1]

    Absolute maximum voltage without damage

    6.3 Vpk-pk

    Typical Specifications

    ADC DC offset

    -11 mV ± 1.6 mV

    Full-scale (FS) input

    1.35 Vpk-pk

    Gain error

    ±1.6% (at DC)

    Average noise density[2]

    nV/√Hz

    64.8

    dBm/Hz

    130.7

    dBFS/Hz

    137.3

    Passband (DC-coupling), real-time sampling mode

    Low cut-off frequency (-3 dB)

    0 Hz

    High cut-off frequency (-3 dB)

    900 MHz

    Signal-to-noise ratio (SNR)[3]

    46.2 dB

    Total harmonic distortion (THD)

    -55.2 dBc

    Spurious-free dynamic range (SFDR)

    56.4 dBc

    Frequency-adjusted DAC range

    ±110 ppm

    Sample rate

    1.5 GHz

    Measurements

    Frequency Response[4]

    Figure 1. Low Frequency Response (Average of Multiple Channels)
    Figure 2. Frequency Response (Average of Multiple Channels)
    Figure 3. Frequency Response, +4 dB to -6 dB (Average of Multiple Channels)

    Spectral Measurements

    Figure 4. Low Power Source Spectral Measurements (262,144 Point FFT, 10 Average RMS, -1 dBFS, 175 MHz)
    Figure 5. Spectral Measurements (131,072 Point FFT, 10 Average RMS, -1 dBFS, 175 MHz)

    Analog Input Total Phase Noise

    Figure 6. AI Phase Noise (100 MHz Input, PLL Locked to PXI_CLK10, 1.2 pS RMS Jitter, -1 dBFS)
    Table 1. Analog Input Total Phase Noise
    Offset Frequency Phase Noise (dBc/Hz)
    100 Hz -98.9
    1 kHz -112.8
    10 kHz -118.2
    100 kHz -126.9
    1 MHz -127.3

    Internal Sample Clock

    General Characteristics

    Oscillator type

    VCXO

    Frequency

    1.5 GHz

    Typical Specifications

    Frequency stability

    Temperature

    ±30 ppm over the operating temperature range

    Aging

    ±5 ppm per year

    CLK IN

    General Characteristics

    Number of channels

    1, single-ended

    Connector type

    SMA

    Input impedance

    50 Ω

    Input coupling

    DC

    Input voltage range

    ± 0.45 V to ± 1.75 V

    Absolute maximum input without damage

    ±5 V

    Duty cycle

    45% to 55%

    CLK OUT

    General Characteristics

    Number of channels

    1, single-ended

    Connector type

    SMA

    Output impedance

    50 Ω

    Output coupling

    AC

    Output voltage range

    ± 0.45 V to ± 1.75 V

    Duty cycle

    45% to 55%

    REF IN

    General Characteristics

    Number of channels

    1, single-ended

    Connector type

    SMA

    Frequency

    10 MHz

    Input impedance

    50 Ω

    Input coupling

    DC

    Input voltage range

    ± 0.45 V to ± 1.75 V

    Absolute maximum input without damage

    ±5 V

    Duty cycle

    40% to 60%

    TRIG

    General Characteristics

    Number of channels

    1, single-ended

    Connector type

    SMB

    Frequency

    10 MHz

    Input impedance

    50 Ω

    Input coupling

    DC

    Interface logic

    VIL

    ± 0.45 V

    VIH

    ± 1.75 V

    VOL

    0.55 V

    VOH

    2.40 V

    Absolute maximum input without damage

    ±5 V

    Maximum retrigger rate

    140 MHz

    AUX I/O (Port 0 DIO <0..3>, Port 1 DIO <0..3>, and PFI <0..3>

    Number of channels

    12 bidirectional (8 DIO and 4 PFI)

    Connector type

    HDMI

    Interface standard

    3.3 V LVCMOS

    Interface logic

    Maximum VIL

    0.8 V

    Minimum VIH

    2.0 V

    Maximum VOL

    0.4 V

    Minimum VOH

    2.7 V

    Maximum VOH

    3.6 V

    Zout

    50 Ω ± 20%

    Iout (DC)

    ±2 mA

    Pull-down resistor

    150 kΩ

    Recommended operating voltage

    -0.3 V to 3.6 V

    Overvoltage protection

    ±10 V

    Maximum toggle frequency

    6.6 MHz

    +5 V maximum power

    10 mA

    +5 V voltage tolerance

    4.2 V to 5 V

    EEPROM Map

    spd-note-caution
    Caution  

    Only write to User Space. Writing to any other offset may cause the NI-5771 to stop functioning.

    Table 2. EEPROM Map
    Byte Address Size (Bytes) Field Name
    0x0 2 Vendor ID
    0x2 2 Product ID
    0x4 4 Serial Number
    0x8 116 Reserved
    0x7C 132 User Space

    Calibration EEPROM Map

    Byte Address Size (Bytes) Field Name
    0x0C 56 Reserved

    Power

    Total power, typical operation

    5.3 W

    Physical

    Dimensions

    12.9 x 2.0 x 12.1 cm (5.1 x 0.8 x 4.7 in.)

    Weight

    413 g (14.6 oz)

    Front panel connectors

    5 SMA, one SMB, and one HDMI connector

    Environment

    Maximum altitude

    2,000 m (800 mbar) (at 25 °C ambient temperature)

    Pollution Degree

    2

    Indoor use only.

    Operating Environment

    Ambient temperature range

    0 °C to 55 °C (Tested in accordance with IEC 60068-2-1 and IEC 60068-2-2. Meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 2 high temperature limit.)

    Relative humidity range

    10% to 90%, noncondensing (Tested in accordance with IEC 60068-2-56.)

    Storage Environment

    Ambient temperature range

    -20 °C to 70 °C (Tested in accordance with IEC 60068-2-1 and IEC 60068-2-2. Meets MIL-PRF-28800F Class 3 limits.)

    Relative humidity range

    5% to 95%, noncondensing (Tested in accordance with IEC 60068-2-56.)

    Shock and Vibration

    Operating shock

    30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC 60068-2-27. Meets MIL-PRF-28800F Class 2 limits.)

    Random vibration

    Operating

    5 Hz to 500 Hz, 0.3 grms (Tested in accordance with IEC 60068-2-64.)

    Nonoperating

    5 Hz to 500 Hz, 2.4 grms (Tested in accordance with IEC 60068-2-64. Test profile exceeds the requirements of MIL-PRF-28800F, Class 3.)

    Compliance and Certifications

    Safety

    This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA C22.2 No. 61010-1
    spd-note-note
    Note  

    For UL and other safety certifications, refer to the product label or the Online Product Certification section.

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:
    • EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • EN 55022 (CISPR 22): Class A emissions
    • EN 55024 (CISPR 24): Immunity
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • AS/NZS CISPR 22: Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions
    spd-note-note
    Note  

    In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended for use only in heavy-industrial locations.

    spd-note-note
    Note  

    Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.

    spd-note-note
    Note  

    For EMC declarations, certifications, and additional information, refer to the Online Product Certification section.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:

    • 2014/35/EU; Low-Voltage Directive (safety)
    • 2014/30/EU; Electromagnetic Compatibility Directive (EMC)

    Online Product Certification

    Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

    For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)

    spd-note-weee
    EU Customers  

    At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.

    电子信息产品污染控制管理办法(中国RoHS)

    spd-note-china-rohs
    中国客户  

    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

    Worldwide Support and Services

    The NI website is your complete resource for technical support. At ni.com/support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers.

    Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and other services.

    Visit ni.com/register to register your NI product. Product registration facilitates technical support and ensures that you receive important information updates from NI.

    A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity. This system affords the user protection for electromagnetic compatibility (EMC) and product safety. You can obtain the DoC for your product by visiting ni.com/certification. If your product supports calibration, you can obtain the calibration certificate for your product at ni.com/calibration.

    NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. NI also has offices located around the world. For telephone support in the United States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the Worldwide Offices section of ni.com/niglobal to access the branch office websites, which provide up-to-date contact information, support phone numbers, email addresses, and current events.

    • 1 For additional information about the ADC in your NI-5771, use the listed part number to locate the appropriate Texas Instruments data sheet at www.ti.com.
    • 2 Average noise density was measured with the following setup conditions: 375 MHz; 262,144 samples; 7-term Blackman–Harris window; bin = 15.059 kHz, 0 dBFS = 6.62 dBm into 50 Ω. (Full scale = 1.35 Vpk-pk).
    • 3 Measured at -1 dBFS with an input frequency of 175 MHz.
    • 4 Referenced at 10 MHz

    Recently Viewed Topics