Table Of Contents

PCI-8512/2 Specifications

Version:
    Last Modified: February 27, 2017

    This section lists specifications for PCI-XNET hardware.

    spd-note-note
    Note  

    Specifications are subject to change without notice.

    Physical Layers

    CAN Physical Layers

    High-Speed CAN

    Transceiver

    NXP TJA1041 or TJA1043

    Max baud rate

    1 Mbps

    Min baud rate

    40 kbps

    CAN_H, CAN_L bus lines

    -27 VDC to +40 VDC

    Low-Speed/Fault-Tolerant CAN

    Transceiver[1]

    NXP TJA1054A or TJA 1055T

    Max baud rate

    125 kbps

    Min baud rate

    40 kbps, 10 kbps min for all error modes

    Single Wire CAN

    Transceiver[2]

    NXP AU5790 or ON Semiconductor NCV7356

    Max baud rate

    83.3 kbps

    Min baud rate

    33.3 kbps

    Bus Power Required

    +8 V to +18 V

    External CAN Transceiver

    Table 1. Digital I/O Characteristics
    Parameter Min Max
    Output0, Output1
    VOH (IOH = -8 mA) 3.8 V
    VOL (IOL = 8 mA) 0.44 V
    NERR
    VIH 2.0 V
    VIL 0.8 V

    FlexRay Physical Layer

    Transceiver

    NXP TJA1080 x 2

    Max baud rate

    10 Mbps

    Min baud rate

    1 Mbps

    LIN Physical Layer

    Transceiver[3]

    ATMEL ATA6620 or ATA6625

    Max baud rate

    20 kbps

    Min baud rate

    2.4 kbps

    Bus Power Required

    +8 V to +18 V

    RTSI/Front Panel Sync Connectors

    Trigger lines

    7 input/output

    Clock lines

    1 input/output

    Front Panel Sync Connectors

    2 input/output (XS/FlexRay only)

    I/O compatibility

    TTL

    Power-on state

    Input (High-Z)

    Response

    Rising edge triggers

    Physical Dimensions

    Dimensions

    10.67 cm x 16.76 cm (4.2 in. x 6.6 in.)

    I/O connector

    9-pin male D-SUB for each port

    Sync connector

    SMB jack x 2 (XS/FlexRay only)

    Power Requirements

    CAN

    +5 VDC (±5%)

    640 mA typical

    +3.3 VDC (±5%)

    940 mA typical

    FlexRay

    +5 VDC (±5%)

    210 mA typical

    +3.3 VDC (±5%)

    940 mA typical

    LIN

    +3.3 VDC (±5%)

    940 mA typical

    Safety

    Isolation Voltages

    Port-to-port ground

    Continuous

    60 VDC, Measurement Category I

    Port-to-earth ground

    Continuous

    60 VDC, Measurement Category I

    This isolation is intended to prevent ground loops.

    Safety Standards

    This product is designed to meet the requirements of the following standards of safety for information technology equipment:
    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA 61010-1
    spd-note-note
    Note  

    For UL and other safety certifications, refer to the product label or the Online Product Certification section.

    Environmental

    Operating temperature

    0 to 55 °C

    Storage temperature

    -20 to 70 °C (Tested in accordance with IEC-60068-2-1 and IEC-60068-2-2.)

    Operating humidity

    10 to 90% RH, noncondensing

    Storage humidity

    5 to 95% RH, noncondensing (Tested in accordance with IEC-60068-2-56.)

    Maximum altitude

    2000 m

    Pollution Degree (IEC 60664)

    2

    Indoor use only.

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:

    • EN 61326 (IEC 61326): Class A emissions; Basic immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions
    spd-note-note
    Note  

    For EMC declarations and certifications, and additional information, refer to the Online Product Certification section.

    spd-note-note
    Note  

    For EMC compliance, operate this product according to the documentation.

    spd-note-caution
    Caution  

    When operating this product, use shielded cables and accessories.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:

    • 2014/35/EU; Low-Voltage Directive (safety)
    • 2014/30/EU; Electromagnetic Compatibility Directive (EMC)

    Online Product Certification

    Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

    For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)

    spd-note-weee
    EU Customers  

    At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.

    Battery Replacement and Disposal

    spd-note-battery-directive
    Battery Directive  

    This device contains a long-life coin cell battery. If you need to replace it, use the Return Material Authorization (RMA) process or contact an authorized National Instruments service representative. For more information about compliance with the EU Battery Directive 2006/66/EC about Batteries and Accumulators and Waste Batteries and Accumulators, visit ni.com/environment/batterydirective.

    电子信息产品污染控制管理办法(中国RoHS)

    spd-note-china-rohs
    中国客户  

    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

    372840L-01

    • 1 NI PXI and PCI XNET interfaces revision E and higher use the TJA1055T transceiver, while revision D and lower use the TJA1054A transceiver. To identify your PCI/PXI NI-XNET hardware revision, refer to the 19xxxx<rev>–4xL text on the green label in the top left corner on the secondary side of the board; <rev> indicates the hardware revision.
    • 2 NI PCI-8513 and NI PCI-8513/2 software-selectable NI-XNET PCI CAN interfaces (revision D and higher) use the ON Semiconductor NCV7356 Single Wire transceiver, while revision C (and lower) uses the NXP AU5790 Single Wire transceiver. NI PXI-8513 and NI PXI-8513/2 software-selectable NI-XNET PXI CAN interfaces (revision E and higher) use the ON Semiconductor NCV7356 Single Wire transceiver, while revision D (and lower) uses the NXP AU5790 Single Wire transceiver. To identify the your PCI/PXI NI-XNET hardware revision, refer to the 19xxxx<rev>–4xL text on the green label in the top left corner on the secondary side of the board; <rev> indicates the hardware revision.
    • 3 NI-XNET LIN hardware uses the Atmel ATA6620 or ATA6625 LIN transceiver for PCI-XNET and PXI-XNET LIN Interfaces, and the NXP TJA1028 transceiver for C Series and Transceiver Cable XNET LIN interfaces. NI PXI-8516 and PCI-8516 XNET interfaces revision F and higher use the ATA6625 LIN transceiver, while revision E and lower use the ATA6620 LIN transceiver. To identify your PCI/PXI NI-XNET hardware revision, refer to the 19xxxx<rev>–4xL text on the green label in the top left corner on the secondary side of the board; <rev> indicates the hardware revision.

    Recently Viewed Topics