Table Of Contents

NI 9862 Specifications

Version:
    Last Modified: February 27, 2017

    The following specifications are typical for the range -40 °C to 70 °C unless otherwise noted.

    High-Speed CAN Characteristics

    Transceiver

    NXP TJA1041AT

    Max baud rate

    1 Mbps

    CAN_H, CAN_L bus lines voltage

    -27 to +40 VDC

    CAN Supply voltage range (VSUP)

    +9 to +30 VDC

    MTBF

    Contact NI for Bellcore MTBF or MIL-HDBK-217F specifications.

    Power Requirements

    Power consumption from chassis

    1 W max (active mode)

    Thermal dissipation (at 70 °C)

    1.25 W max (active mode)

    Physical Characteristics

    To clean the module, wipe it with a dry towel.

    Weight

    Approx. 144 g (5.0 oz)

    Safety

    Connect only voltages that are within the following limits:

    Maximum Voltage[1]

    Port-to-COM

    -27 to +40 VDC max, Measurement Category I

    Isolation
    Port-to-earth ground

    Continuous

    60 VDC, Measurement Category I

    Withstand

    500 Vrms, verified by a 5 s dielectric withstand test

    Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics.

    spd-note-caution
    Caution  

    Do not connect the NI 9862 to signals or use for measurements within Measurement Categories II, III, or IV.

    Safety and Hazardous Locations Standards

    This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA 61010-1
    • EN 60079-0:2012, EN 60079-15:2010
    • IEC 60079-0: Ed 6, IEC 60079-15; Ed 4
    • UL 60079-0; Ed 6, UL 60079-15; Ed 4
    • CSA 60079-0:2011, CSA 60079-15:2012
    spd-note-note
    Note  

    For UL and other safety certifications, refer to the product label or the Online Product Certification section.

    Hazardous Locations

    U.S. (UL)

    Class I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, AEx nA IIC T4

    Canada (C-UL)

    Class I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, Ex nA IIC T4

    Europe (DEMKO)

    Ex nA IIC T4 Gc

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for sensitive electrical equipment for measurement, control, and laboratory use:

    • EN 61326 (IEC 61326): Class A emissions; Industrial immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions
    spd-note-note
    Note  

    In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia and New Zealand (per CISPR 11) Class A equipment is intended for use only in heavy-industrial locations.

    spd-note-note
    Note  

    Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.

    spd-note-note
    Note  

    For EMC declarations and certifications, and additional information, refer to the Online Product Certification section.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:

    • 2014/35/EU; Low-Voltage Directive (safety)
    • 2014/30/EU; Electromagnetic Compatibility Directive (EMC)
    • 2014/34/EU; Potentially Explosive Atmospheres (ATEX)

    Online Product Certification

    Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

    Shock and Vibration

    To meet these specifications, you must panel mount the system.

    Operating vibration

    Random (IEC 60068-2-64)

    5 grms, 10 Hz to 500 Hz

    Sinusoidal (IEC 60068-2-6)

    5 g, 10 Hz to 500 Hz

    Operating shock (IEC 60068-2-27)

    30 g, 11 ms half sine; 50 g, 3 ms half sine; 18 shocks at 6 orientations

    Environmental

    Refer to the manual for the chassis you are using for more information about meeting these specifications.

    Operating temperature (IEC 60068-2-1, IEC 60068-2-2)

    -40 °C to 70 °C

    Storage temperature (IEC 60068-2-1, IEC 60068-2-2)

    -40 °C to 85 °C

    Ingress protection

    IP40

    Operating humidity (IEC 60068-2-78)

    10% RH to 90% RH, noncondensing

    Storage humidity (IEC 60068-2-78)

    5% RH to 95% RH, noncondensing

    Pollution Degree

    2

    Maximum altitude

    2,000 m

    Indoor use only.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

    For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)

    spd-note-weee
    EU Customers  

    At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.

    电子信息产品污染控制管理办法(中国RoHS)

    spd-note-china-rohs
    中国客户  

    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

    373243E-01

    • 1 The maximum voltage that can be applied or output between any port or VSUP terminal and a COM terminal without creating a safety hazard.

    Recently Viewed Topics